When we have received a return back which can no longer sell as new, we post it here.
The product gets discounted and will DRIP in price daily until it is sold. You can wait for it to get to a lower price, but once it's sold, it's gone.
See each product for information regarding the daily DRIP rate, condition, and photos of any issues.
Instant and infinite sparkling water at your fingertips whenever you want it! Benchy connects to your household's water supply, chills, carbonates, and delivers on demand Serve up to 8 gallons of chilled, carbonated water per hour Pair with draft faucets and place it on your counter, or install it under the counter and plumb it to a mounted water faucet See below for detailed installation video Benchy Sparkling is the answer for instant chilled and carbonated water on demand. Simply connect your household water supply and CO2 Cylinder to the unit and receive unlimited sparkling and chilled water from the draft faucets. The chiller is highly efficient with very little power draw while idle and has enough cooling capacity to serve up to 8 gallons of sparkling water per hour. This unit comes without shanks or draft faucets, as it can be used as a countertop unit or installed under your counter and routed to a faucet you install on your counter or kitchen sink. If you plan to use it as a countertop unit, we highly recommend NukaTap Flow Control Faucets. Easy Installation: Plug the Benchy into the wall Fill internal water tank Connect household water supply Connect CO2 Cylinder Pour chilled sparking water. It's that simple and you can be enjoying chilled sparkling water in under 1 hour with this setup and barely any time at all to cool down. Ensure that the unit is installed and operated according to the instruction manual which can be found below. Fully Adjustable The Benchy Sparkling has an integrated digital temp controller so you can control the temperature from 0.5-10°C (33-50°F). You can also vary the carbonation level from 0.5 volumes to over 5 volumes for super bubbly water. Cooling Performance The Benchy Sparkling is able to chill about 5 to 8 gallons of sparkling water per hour (based on ambient water and air temperature of 68°F). To further increase the capacity of this unit, you can pre-chill the water from your household supply line either by a holding tank (ball lock keg) in the fridge or a DraftMaster Chiller. If you pre-chill the water you can more than double the output of the Benchy Sparkling. The reservoir temperature on the Benchy should never be set below 2°C (35°F) as you will run the risk of freezing the water inside the carbonation keg. Specifications: 110V Refrigerant: r600a (80 grams) Cooling Power: 600 watts Power Consumption: 155 watts (idle power consumption less than 5 watts) Capacity: approximately 6.6 gal/hour (based on 68°F ambient temperature) Input Gas: CO2 @ 29-50 psi (Requires 8mm (5/16") OD tubing) Input Water: Must be 15 psi higher than gas pressure (Requires 6.35mm (1/4") OD tubing) Sparkling/Chilled Water Out: Requires 8mm (5/16") OD tubing Dimensions: 18.3" H x 11.4" W x 20.5" D (Excluding sight glass that can be removed) Recommended Accessories: CO2 Gas Cylinder CO2 Regulator EVABarrier 4mm x 8mm Tubing PE Water Line Tubing 6.35mm Duotight In-Line Regulator (0-150 psi) Duotight Reducer - 8mm x 6.35mm 8mm Duotight Check Valve Diverter Valve (check water line connection for the size you'll need) Countertop Installation Recommended Accessories: (2) Short Shanks & Hex Nuts (2) Duotight Adapters - Beer Thread x 8mm (2) NukaTap FC Faucets& Self Closing Springs (2) Tap Handles (of your choice) Tube Cutter Faucet & Shank Wrench KegLand Part Number: KL2068
$989.99 $883.89
25 Feet of 3/8" Copper Coils Raised Up To Where The Heat Is Integrated Turbulator Cools Faster and Uses 40% Less Water 25 Feet of 3/8" Copper Includes Tubing and Standard Garden House / Utility Sink Thread Manufactured in the USA Save water during the cooling process with our Super Efficient Immersion Wort Chiller. During the manufacturing process we build in an inner water turbulator that causes the cold water to spin through the coil. This reduces the laminar flow found in a standard wort chiller where only the outer water is cooled as it travels through the coil. The result is a 40% reduction in water, and faster cooling, when compared with our standard chillers. But that is when we compare it to OUR standard chillers with the coils at the top. When you compare to other chillers on the market the results are even better. ALL of our chillers feature coils that raised up to where the heat is. As we learned in school heat rises so when other wort chillers have all the coils on the bottom they actually never cool unless you stir your wort. The problem with stirring is that you mix up all your trub/sediment and you risk airborne contamination... neither of which is good. Our chillers cool fast and allow you to keep your lid on your kettle during the critical cooling period. Constructed from 25' of 3/8'' copper tubing. 8' of vinyl tubing attached to both the in and the out with a female garden hose fitting on the in side. Use our CE21S hose thread adaptor to attach to your sink. Perfect for a kitchen environment where the sink is close by. This size chiller is ideal for our 8 Gallon Heavy Duty Kettles! The measurements are: Approx. 10" diameter, 8" to the top coil, 15" to the bend to go over the lip of the kettle.
$104.99 $94.21
Far from your average coffeemaker, the Brazen Plus is a fully customizable unit allowing for total control over your brew. The Brazen Plus brew system has features not found on any other consumer coffee maker. Settings are adjustable for water brewing temperature and pre-soak like found on many commercial brewers. Set your brewing temperature between 190–210°F / 90–99°C with accuracy to within 1-degree Fahrenheit. A patented feature allows temperature calibration with altitude correction. The oversized shower head and pulsed water flow ensure complete coffee bed saturation for terrific coffee extraction. Permanent filter included or use paper filters. Thermal carafe (SCA approved) with brew through lid keeps coffee hot. The Brazen Plus 3.0 is one of the very few that meet the Home Brewer certified by the Specialty Coffee Association of America to their standards. 3.0 Updates: New Universal System Power Boards New Program: revised Pulse Water Release Timing for better extraction New Micro Controller: faster data refresh Features: Capacity: 1.2 Liter, 40oz, 8 (5oz) cups Temperature Control: Set brewing temperature from 190–210°F (90–99°C) Programmable Brew Start Time: Wake up to coffee with timed brew setting Ideal Coffee Extraction: Coffee grounds are fully saturated due to oversized showerhead and pulsing of the water flow. Patented Sensor Calibration: sensor calibration for consistent temperature accuracy Elevation calibration: Adjust your brew temperature based on elevation to achieve a hot cup of coffee regardless of how far above sea level. Thermal carafe with brew through lid keeps coffee hot (SCA approved) Adjustable time for Pre-soak: Allows the coffee to bloom before brewing for better flavor Stainless steel water reservoir (SUS304): that’s easy to fill Stainless Steel Thermal Valve: Water release Permanent gold filter: Included or use paper filters (10 cup for max benefit/ extraction) Memory save: Settings remain, even if the power goes out. Sleep mode: Saves power when not in use
$219.00 $191.05
Elevate your brewing game with the 220V Gen 4 BrewZilla. This cutting-edge system combines more power with innovative features like wireless connectivity via WiFi & Bluetooth, allowing you to heat faster while you control and monitor your brew day, ensuring precision, convenience, and exceptional beer batch after batch! WiFi / Bluetooth enabled RAPT Controller tracks your brewday and automatically uploads detailed information to the RAPT portal The top mounted RAPT Controller can be tilted upward for easy viewing, or detached from the unit to mount it on the wall or placed on your bench Mirror polished dome shaped bottom with center drain — get every last bit of wort into your fermenter while the perforated bottom screen filters out 95% of hot break and hop matter Make larger batches or higher gravity beers! BrewZilla offers the largest malt pipe capacity for units in its size range, and the Gen 4 unit has a 30% larger malt pipe compared to the previous generation Perforated bottom on the newly designed malt pipe allows for improved mash recirculation flow without sacrificing efficiency Element power percentage can be adjusted via the RAPT Controller. Go full power to heat up quickly, or dial it down so you don’t overshoot your strike water temp The built-in pump is plumbed to both the recirculation and arm and the bottom ball valve. Recirculate wort during your mash, then close the recirculation valve and pump wort to your fermenter via the bottom valve Pair with the RAPT-enabled Bluetooth Thermometer, allowing your BrewZilla to calculate a core mash temperature reading and more accurately control temperatures and mash steps More RAPT-enabled accessories are coming, and future firmware updates can be downloaded to the RAPT Controller itself over the internet WiFi/Bluetooth Enabled RAPT Controller The RAPT Controller is mounted to the top of the boiler body, allowing for easy operation when you have the unit set on the ground. The controller can be tilted upwards to give you an even better view, or it can be removed from the BrewZilla entirely if you’d prefer to mount the controller on your wall or lay it down on a workbench. From the controller, you’ll orchestrate your entire brew day. Program mash steps, dial in element power, and operate the integrated pump all from one screen. But the RAPT Controller is much more than a beautiful, full-color display switch board. Once synced to the RAPT Portal, you’ll be able to track, record and monitor your brews online. No need for handwriting notes or punching brew day details into your phone – all of the data from your brew is automatically logged to your portal profile. This information doesn’t just include your mash profile; it also captures detailed information about your element power and pump activity, opening the door for very precise repeatability. And the RAPT Portal isn’t just a digital archive for your brew days. With your BrewZilla powered on, you can control your brewery from virtually anywhere using your phone’s web browser. Not sure when you’ll be home from work or your kid’s ball game going into extra innings? No problem! Before you head out, simply log into the RAPT Portal from your phone and tell the BrewZilla to start heating your strike water. Along with remote control, the portal enables you to program alarms and push notifications for all of your boil additions. We’ve all been caught up with a side task and failed to throw in that yeast nutrient or clarifying agent at the end of the boil, but the BrewZilla has the back of even the most forgetful brewer! But wait, there’s more! In addition to WiFi connectivity, the RAPT Controller is also a Bluetooth gateway device. KegLand is currently developing various Bluetooth devices such as the Bluetooth Beacon Thermometer and other sensors which will be compatible with your brewery upon release. The RAPT Controller is able to receive information from Bluetooth Low Energy (BLE) devices, adjusting its processes based on this new stream of information while simultaneously logging it to your RAPT Portal. With the Bluetooth Beacon Thermometer, for example, you’ll be able to feed temperature readings from the top of your mash bed to the controller. The controller will then compare this reading with the main temp probe reading at the base of the kettle and adjust element cycling based on these combined readings. Finally, the RAPT Controller WiFi connectivity allows you to update the controller’s firmware with a single click. Take advantage of new features and accessories as soon as they become available by simply keeping your BrewZilla connected to your local WiFi network. And again, the WiFi is already built-in! No need to come back for an expensive add-on accessory down the road. High Capacity Malt Pipe With an approximately 23.5 lb capacity, the BrewZilla can mash nearly 50% more grain than similar sized models of the Anvil Foundry and Grainfather G30. If you want to fill your fermenter with more than a 5-gallon batch worth of wort, or brew the highest gravity beer recipes, the BrewZilla is the brewhouse for the job. And the included malt pipe is just the beginning. If you want to expand your brewery’s grain capacity even further, KegLand makes Boiler Extension Kits and Extended Malt Pipes for that very purpose. The malt pipe features a perforated section at the bottom which improves mash recirculation flow without sacrificing efficiency. Concave Base with Center Draining Leave no wort behind! The concave base with center drain means you’ll be able to extract every last drop of wort to your fermenter. If you’ve brewed in a traditional flat bottom kettle, this center drain may be a bit perplexing at first. Many brewers are used to whirlpooling after the boil to pull hop matter into the center of the kettle, then transfer out using a pick-up tube that pulls from the kettle wall in order to avoid sucking up the solids. But fear not! One of the key features of the BrewZilla is the false bottom protection screen. This screen avoids the need for doing a whirlpool, filtering wort as it transfers and blocking more than 95% of hops and hot break from getting sucked into the pump. This not only prevents blocked pump issues, it also increases the efficiency of your brewhouse by eliminating kettle loss from wort that may have otherwise been left behind. Ultra Low Watt Density Elements The concave base on the BrewZilla also allowed for larger heating elements with significantly lower watt density than other breweries. When a lot of energy is coming off of a small element, the local temperature near the element can be so high that it scorches the wort and causes caramelization. Lower watt density essentially means you can produce lighter color beers that would otherwise have fallen victim to caramelization effect. It also reduces that chance of boilovers and reduces stress on the elements which extends their life expectancy. Easy Access Built-In Pump The built-in pump allows you to recirculate your wort during the mash for improved efficiency and more even temperature distribution. But it can also be used to transfer your wort from kettle to fermenter rather than relying on a gravity feed, and with the optional CIP Rotar, you can used the pump to clean your BrewZilla (or fermenter) after every use. During your brew day you’ll be able to control the pump from the RAPT Controller with a dedicated button for turning the pump on and off. Another feature you’ll find on the controller is adjusting the pump flow. This doesn’t control the actual volume of the flow (you can do that from the ball valve located on the recirculation arm), but rather cycles the pump on and off automatically based on your setting. At 100%, the pump remains on continuously. But at 80%, the pump will cycle to be on 80% of the time and off 20% of the time. This may not be a feature that every brewer thinks they need, but it’s an excellent way to avoid running the pump dry accidentally, as the time the pump is off allows recirculating wort to filter through the grain bed and back into the pump inlet. If you flip over the boiler, you’ll find the magnetic drive pump and all the plumbing is right at your fingertips. This means you don’t have to disassemble the base in order to access the pump for cleaning or maintenance if required. It also means the plumbing can be changed more easily too. For instance, the unit comes as standard with the plumbing from the pump feeding both the recirculation arm and the transfer valve, but you change this so the tap outlet bypasses the pump if you prefer. MoreBeer!'s Final Word We’ve been selling all-in-one brewing systems ever since they first hit the market, and we have to say that the Gen 4 BrewZilla is not only the most feature-packed unit ever made, it’s also offered at an incredibly competitive price point when compared to other systems. You’ll get all of the cutting edge Bluetooth technology you’d get with the Grainfather and at an exceptionally lower price tag. Plus, you get the WiFi capabilities as standard, rather than as a $100 add-on accessory. When it comes to mash recirculation, that’s yet another built-in feature on the BrewZilla, and the pump can also be used for transferring and CIP cleaning. The Foundry has a great starting price, but if you want to unlock its full potential, you’ll need to spend another $100 for the recirculation pump kit. What’s more, no other system in the same ‘weight class’ has the same grain capacity. And if the standard capacity isn’t quite enough, the BrewZilla can be easily upgraded with a Boiler Body Extension Kit and Extended Malt Pipe. When you purchase the BrewZilla, you can feel confident that you’re investing in a top shelf system and all of the critical features you’re expecting will be included. Perfect for Distillation If you want to expand your lineup of homemade libations to offer Spirits in addition to Ales & Lagers, the BrewZilla makes an excellent pot still! Add the Distillation Lid upgrade and pair it with an AlcoEngine Copper Reflux Condenser or Copper Pot Still Top. AlcoEngine Stills have been selling on the home market for years and offer some of the most affordable, beginner-friendly stills you'll find. Features: Gen 4.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons WiFi/Bluetooth Enabled RAPT digital temperature controller Automatic step mashing with 6 programmable stages 220-240V power NEMA 6-30P plug Requires NEMA 6-30R receptacle Requires 11 amps from 30 amp circuit Dual heating elements (1900 watts and 500 watts) Stainless steel 1/2" ball valve for gravity draining or transferring via pump Immersion wort chiller included Stainless steel malt pipe/basket Stamped in volume markers Glass lid Adjustable lid clamps (do not use with glass lid in place - see below) Magnetic drive pump for recirculation, transfers, and cleaning Recirculation arm PPSU sight glass Bottom handle for easy lifting and pouring Rubber feet Temperature reads in °F or °C Approximately 32.75" H (with recirculation arm) x 12.5" D Recommended max. grain bill: 23.5 lbs AlcoEngine Still ready with the purchase of a Distillation Lid Pump Specs: Max Capacity: 2.9–3.1 gal/min Max Head: 4.9–6.8 ft. Poles: 2 Voltage: 220–240V-AC Frequency: 50–60Hz Power: 6 watts Current: 60 mA Speed: 2600–3000rpm Duty Cycle: Continuous Capacitor: 2µF Input/Output: 13mm barb Water Resistance: IPX2 You Will Need: 2' of H985 1/2" ID Silicone tubing for sparging and draining. To connect included Chiller: (20') of D1710 1/2" ID beverage tubing (or whatever length required, (3) H950hose clamps and (1) brass hose by thread adaptor (H508). These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout. KegLand Part Number: KL27434 Please note: due to patent restrictions in the United States, the malt pipe has been redesigned with one set of bottom feet. This model does not include the "two stage" malt pipe as advertised by KegLand and featured in previous MoreBeer! YouTube videos. Please Note: When removing the malt pipe to drain after mashing, it is important to do so slowly rather than in one swift pull. If the malt pipe is removed all at once when it is full of wort, it is possible for the draining wort to spray out and over the rim of the brewery through the perforated bottom. Remove the malt pipe slowly so that some of the wort can drain out before it is fully removed and set on its bottom feet. This can be done by hand on the 35L unit, but for the 65L and 100L units we highly recommend using the Pulley System for removing the malt pipe. Warning: Do not engage the adjustable lid clamps when brewing with the BrewZilla's standard glass lid. The clamps are only intended to be used with distillation lids or other metal accessories. With too much tension, it is possible for the lid clamps to break the glass lid when engaged. Warning: If you are going to use an extension cord with the BrewZilla, you must ensure that the cord is the correct gauge and properly rated to suit the power requirements of your brewery. See the reference chart below for the recommended gauge based on your unit and the length of cord you wish to use. 35L (110V) 35L (220V) 65L (220V) 100L (220V) 10 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 25 ft. 14 Gauge 14 Gauge 12 Gauge 10 Gauge 50 ft. 12 Gauge 12 Gauge 10 Gauge 8 Gauge RAPT Gen 4 BrewZilla | User Manual
$599.99 $523.42
Portable, Inline, Keg Dispensing unit that can be powered via 110V outlet Replaces a traditional Draft Box/Jockey Box with no ice required Differs from the regular Komos Kryo Inline Chiller in that there is no glycol reservoir / The Nomad is liquid-free and easier to transport Can chill up to 2 gallons of room temperature beer, inline, per hour NukaTap Flow Control Faucets, tap handles, and drip tray included Mobile draft dispensing has never been easier with the KRYO Nomad electric keg dispenser. As with a jockey box, beer is chilled inline as it passes from the keg through the internal draft coils which are chilled by the electrically powered solid carbon based heat sink. With a standard 110V outlet, you can serve ice cold beers from an unchilled keg, and unlike the KRYO glycol unit, this model is absolutely liquid-free, making it the ideal choice for mobile draft dispensing. No need to wait an hour for glycol solution to chill, once you power on the Nomad, you'll be ready to go in as little as 15 minutes! Carbon Heat Sink The secret to the KRYO Nomad's incredible chilling capacity and portability is the solid carbon based heat sink. This heat exchange technology requires no liquid whatsoever, so you'll never run into issues with emptying or spilling coolant when you transport this chiller from place to place. It provides roughly 300 watts of cooling power which allows you to chill about 2 gallons of beer per hour. Just be sure to give the unit about 2 minutes to recover for each 16 oz pour. The Nomad is very power efficient, drawing only 60 watts of power when the compressor is running. When idling, the chiller uses only 1.6 watts of power, meaning it it averages only 15 watts of power draw when turned on and periodically cycling the compressor. NukaTap Flow Control Faucets These stainless steel forward sealing faucets allow you to make instant adjustments to the beverage flow as you pour. A perfect faucet for those who often switch between beer styles with different carbonation levels. No need to rebalance your lines or play with your regulator settings. Adjust the flow control level to dial in the flow rate and pour perfect pints every time! They also have the lowest thermal mass and best laminar flow design to further reduce foaming issues. Duotight Bulkheads Draft lines connect directly to 8 mm Duotight bulkheads located at the rear of the unit. To hook up your kegs to the KRYO Nomad, we highly recommend EVABarrier draft line and Duotight fittings—the same lines and fittings that come standard with our KOMOS Kegerators. 8 mm OD EVABarrier plugs directly into the bulkheads, then depending on what type of kegs you'll be pouring, you can use these Duotight Female Beer Thread Adapters for sanke keg couplers if you'll be dispensing commercial kegs, or for homebrew kegs, we recommend Duotight Flare Adapters for your QDs, or if you're starting from scratch, consider the Duotight Ball Lock Quick Disconnects. Includes: (2) NukaTap Stainless Flow Control Faucets (2) Tap Handles Stainless Countertop Drip Tray w/ Removable Grill Features: Chill 2 gallons of beer per hour (based on 68°F ambient) Duotight bulkheads compatible with 8 mm OD EVABarrier tubing AC Voltage via IEC Plug: 110-120V Max Power Draw: 300W Dimensions: 9.25" x 13.7" x 18.1" (not including faucets / drip tray) CE Certified Temp Controller: Follow these steps to adjust the SET temperature on the controller. Press and release the 'SET' button to enter into the user menu. Press 'SET' will display the value of the target temperature setting. Press the 'Up' or 'Down' button to increase or decrease the set temperature. Press the snowflake icon button or wait 30 seconds and the controller will save the setting and return to normal operation mode. Warning: Do not set the temperature controller lower than 28°F (-2ºC). Running the unit below this temperature may negatively affect the unit's efficiency and has the potential to freeze beer which may impact the finished beer's flavor.
$699.99 $628.73
You have seen 101 out of 101 products
